Pretty sure this is David's Frenzy on a J-315 Redline:
Chris' rocket on a J-500 Mojave Green:
[video=youtube;vFvJHKVZ8jw]https://www.youtube.com/watch?v=vFvJHKVZ8jw[/video]
Robert H. and Frank D., pretty sure these are yours but I need some help:
[video=youtube;7vW76ydQPqQ]https://www.youtube.com/watch?v=7vW76ydQPqQ[/video]
and
[video=youtube;LAG6lyKdM8M]https://www.youtube.com/watch?v=LAG6lyKdM8M[/video]
Congrats to Sam on his L2 also. Check out the Medusa Nozzle.
...
Sam, the same pics on our shutterfly page are much better TRF requires complete destruction of the resolution to upload.
Congrats to Sam on his L2 also. Check out the Medusa Nozzle.
View attachment 267604 View attachment 267606 View attachment 267607 View attachment 267608 View attachment 267605
Sam, the same pics on our shutterfly page are much better TRF requires complete destruction of the resolution to upload.
Dare we start a new launch thread on the tentative Corsicana HP launch at the end of August?
Sorry for the late DARS / Hearne entries -- been a tough week at the mill.
Sam and his L2 flight:
[video]https://youtu.be/5-o95ursdyI[/video]
Chris' Cherokee flight:
[video]https://youtu.be/6G2BC2b4LEg[/video]
Pix of the event:
https://darsrocketrypics.shutterfly.com/pictures/2028
Sorry for the late DARS / Hearne entries -- been a tough week at the mill.
Sam and his L2 flight:
[video]https://youtu.be/5-o95ursdyI[/video]
Chris' Cherokee flight:
[video]https://youtu.be/6G2BC2b4LEg[/video]
Pix of the event:
https://darsrocketrypics.shutterfly.com/pictures/2028
Sorry for the late DARS / Hearne entries -- been a tough week at the mill.
Sam and his L2 flight:
[video]https://youtu.be/5-o95ursdyI[/video]
Chris' Cherokee flight:
[video]https://youtu.be/6G2BC2b4LEg[/video]
Pix of the event:
https://darsrocketrypics.shutterfly.com/pictures/2028
...
Sam, what delay tool were using to drill down your 54 RMS delay element? The one in the photo appears to be a UDDT. Although it's coined as "Universal" it's actually not quite....
[video=youtube;5rLBHrDI8PA]https://www.youtube.com/watch?v=5rLBHrDI8PA#t=18[/video]
Very nice, thank you. What about more pictures of ANDRAC ? That was the best L2 cert flight of the day !
That was the one. Definitely an early deployment, could have used at least another second and maybe two. I think I was bearing down a little too hard with the drill. My sim said 9 seconds and I'll be re-running that a few more times before I fly again.
Hmmm, I'm pretty sure you should be using the "RDDT" in 54, item number TO82510-2. It's used specifically for drilling RMS delays. Come to think of it, I don't even show that on my site.... I do have the 38mm version (item TO82510-1) for RMS delays but not the 54 https://www.buyrocketmotors.com/aerotech-18-38mm-rms-delay-drilling-tool-rddt/
Take a look here on AT's website https://www.aerotech-rocketry.com/news.aspx?y=2011
Not sure why AT calls the tool you used the "Universal Delay Drilling Tool" as it's not universal, at least not yet. It's only for DMS and RMS-EZ's right now.
Robert H. and Frank D., pretty sure these are yours but I need some help:
[video=youtube;7vW76ydQPqQ]https://www.youtube.com/watch?v=7vW76ydQPqQ[/video]
Enter your email address to join: