Sunward - The Screamer

The Rocketry Forum

Help Support The Rocketry Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

JAL3

Well-Known Member
Joined
Jan 17, 2009
Messages
14,333
Reaction score
268
The Screamer is my first try at a kit from Sunward Aerospace. I've used their components before but have not gotten around to trying a kit until now. This one caught my interest because it is a 2x cluster; and I like clusters, and alos because of its canted motor design. There are other canted motor designs but this is one I've only seen ads for and have never seen a real example in person or through photos. That changes now.

screamer.jpg

TSc-face-card.jpg
 
Last edited:
The first step given in the instructions is to cut out the wrap around guide. It is printed on a sheet by itself along with a couple of paper strips intended for engine hook reinforcement. I generally prefer the wraps over other methods. The wrap was cut out and set aside. I did not cut out the reinforcing bands.

TScwrap-guide-1.jpg
 
The motor mounts were up next. A pair of marks was made one each tube at 3/16" and at 1-3/4". A slit was made at the aft mark and the engine hook inserted. At this point I was instructed to use the paper reinforcemnt wraps which had been provided but I elected to use electrical tape instead. I have long heard of its use in this capacity and intended to give it a try but never seemed to have any one hand. Now I do and I'm giving it a try. The tape was wrapped around each mount as the second mark.

TSc-motor-mount-1.jpg

TSc-motor-mount-2.jpg
 
The next step was a simple matter of seating the thrust rings right above the engine hooks with yellow glue.

TSc-motor-mount-3.jpg
 
Next came what the instructions described as the "most tedious part of the build". It was time to work on the canted housing. I was instructed to make a line across the center of the rear ring. I did so and was pretty please with myself until I realized that I had run it in the wrong direction. I had to make another line at a right angle to the first. The wedge peice was then glued in place with yellow glue and allowed to set.

TSc-motor-mount-4.jpg

TSc-motor-mount-5.jpg
 
Next up was a problem. The forward ring in my package was broken into 2 pieces.

NOTE: this should not be taken as a reflection on Sunward Aerospace. It looks to be a delicate part at the best of times and this kit spent more than its share of time floating around boxes and such.

I decided to try and glue the two pieces together. It may work. At worst, I will have to wait as a replacement order comes in. Accodingly, a dab of yellow glue was placed on the break and the 2 pieces were pushed together.

TSc-motor-mount-6.jpg

TSc-motor-mount-7.jpg
 
After a night to let the glue dry on the angle, I took one of the motor tube and test fitted it in the lower ring/angle. The lunette at the bottom of the ring has a notch cut out of it to accomodate the engine hook. I got this lined up and then set it in place with the edge of the motor tube flush with the top of the angle. It looked like it fit so I applied the first layer of a double glue joint, pressed the mount into place and then removed it. A bit later, some more glue was applied and the mount put into place again. I found that I needed to tape the mount down in order to keep it properly aligned.

TSc-motor-mount-8.jpg
 
The first tube dried in the mount overnight and I removed the tape to inspect the results. It seemed OK although there are a few gaps between the tube and the angle support. Not having built something like this before I am unsure.

TSc-motor-mount-9.jpg
 
Assuming that everything was alright, I tried the other mount and found it to be much the same as the first. It was again fitted with a double glue joint and taped into place to dry.

TSc-motor-mount-10.jpg
 
To start off the waiting process, I decided to work ahead a little bit. The next step was to put the wrap in place for the cutting of the tube. It was taped in place and fit perfectly, always a relief for me. It was aligned so that it was flush with the aft end and a piece of tape was used to hold it down.

TSc-BT-1.jpg
 
With the guide in place, the first task was to cut out the notches for the canted motors. I knew this was going to be done better if I did it right so I took some time to make a mandrell to support the tube as it was cut.

Micromeister was kind enough to send me some information on his system and it is one I'm working towards but have not completed. Now, with the beginning of the BT60 mandrell, I have at least started.

I took a piece of the largest diameter wood dowel I had and cut off an 18" length. I then took some duct tape and started to slowly wrap it around one end in order to build the diameter up. I tried to do it slowly and prevent wrinkles and mostly succeeded though it was a long and monotonous task. I stopped when the wrapped end of the dowel just fit into the BT.

BT60-mandrell-1.jpg

BT60-mandrell-2.jpg
 
The mandrell was inserted into the aft end of the BT, the end with the guide taped to it, and positioned so that the sutting area was supported. A razor knife was then drawn repeatedly over the marked line until the indicated segments were removed. At this point, I needed to test fit the motor mount but that was still drying so I went on to other projects for a while.

TSc-BT-2.jpg

TSc-BT-3.jpg

TSc-BT-4.jpg

TSc-BT-5.jpg
 
When the motor mount had dried, I took off the tape and tried to test fit the mount into the body tube. It seemed to fit just fine and I almost forgot that I had not yet put in the forward centering ring. That too had been drying from my patch job but the connection was so thin that it did not hold up to my manipulations. I decided I would have to try and glue it in place in pieces. While test fitting, I also had the realization of why paper wraps were provided to reinforce the engine hooks instead of tape being specified. The mounts are visible!

DOH!!!!!

TSc-motor-mount-11.jpg
 
The fins, contrary to what was indicated in the instructions, were loose and not in any way joined to the parent stock material. They were of good quality and cleanly cut. I followed the instructions and just rounded the leading edges. You need to make sure you identify the proper grain direction!

I brused on some Elmer's filler, screeded it with a razor blade and set them aside to dry.

TSc-fins-1.jpg

TSc-fins-2.jpg
 
Truning my attention back to the motor mount, I decided to let the split forward ring work for me. The kit is provided with a trifold mount for the shock cord. I absolutely detest these. I decided to use a fat piece of Kevlar instead. I knotted the Kevlar at one end and treaded it though the space between the two motor mounts. I then slathered yellow glue over it, fixing it to the triagular support. When dry, I applied some more glue.

TSc-motor-mount-12.jpg
 
The nose cone was not like the fins. Instead of being smooth, it was one of the fuzziest I had ever seen. I slathered on the filler and set it aside to dry.

TSc-NC-1.jpg

TSc-NC-2.jpg
 
Though I did not manage to glue the pieces of the forward centering ring back together and have them stay together, I did manage to glue the pieces into the right place on the motor mount. When dry, they even fit well!

TSc-motor-mount-13.jpg
 
Since the dry fitting went well, I swabbed the tail of the BT with yellow glue and inserted the mount. It seemed steady and I hoped for the best.

TSc-motor-mount-14.jpg

TSc-motor-mount-15.jpg
 
It was time to start mounting the fins. I removed the wrap and used an angle to extend the fin lines. A pushpin was then used to make perforations along the lines in the hope of forming a better glue joint.

TSc-BT-6.jpg
 
Then it was a matter of beginning to glue on the fins. I used yellow glue and a double glue joint.

TSc-fins-3.jpg
 
The gluing of the fins took place over the course of 3 days. I wanted to let the first glue joing dry completely before doing the second and attaching the fins.

TSc-fins-4.jpg

TSc-fins-5.jpg

TSc-fins-6.jpg
 
When the fins had dried in place, I began the process of filleting them with white glue.

TSc-fins-7.jpg
 
The filler on the nose cone had had a chance to dry and I sanded it down. That dramatically improved things but I was still having a problem with the fuzzies peeking through. I went ahead and glued in the eye screw and then began to drizzle thin CA over the nosecone in the hope that it would harden things up and made it sand easier.

NOTE TO SELF: Do not drizzle CA while barefoot on a concrete floor.

TSc-NC-3.jpg
 
There has been progress today, just nothing worth taking pictures of.

Fillet, smooth, dry, rotate, repeat.
 
After what seemed like an excessing amount of filleting, the Screamer seemed ready to move to the finishing stage.

TSc-assembled-1.jpg
 
The fins had been sealed with Elmer's Filler and sanded during construction. Now what needed to be done was to prime the rocket. It was taken to the booth and given a coat of Kilz. Because of the way the rocket was stood up, it was apparent that another good coat would be needed to complete the job.

TSc-primed-1.jpg

TSc-primed-2.jpg
 
Another coat was applied and then the rocket was sanded down with #400 sandpaper. It was then set up in the booth and sprayed with my dwindling supply of the old Krylon gloss white.

TSc-white-1.jpg

TSc-white-2.jpg
 
I wound up putting on three coats of the gloss white and the result was satisfactory. The rocket was then masked for yellow, leaving only the nosecone and fins exposed.

TSc-masked-for-yellow-1.jpg

TSc-masked-for-yellow-2.jpg
 
The rocket was put in the booth and given three light coats of a medium/light yellow. Even with the masking, the added bit of color really added a lot to the appearance.

TSc-yellow-1.jpg

TSc-yellow-2.jpg

TSc-yellow-3.jpg
 
Back
Top