Six Pack ( Impulse Aerospace / Rocket Vision / Rugged Rockets )

Discussion in 'Yard Sale / Wanted' started by dhbarr, Dec 19, 2016.

Help Support The Rocketry Forum by donating:

  1. Dec 19, 2016 #1

    dhbarr

    dhbarr

    dhbarr

    Amateur Professional

    Joined:
    Jan 30, 2016
    Messages:
    5,302
    Likes Received:
    439
    I'm looking for one of these, dead or alive. I have the .rkt from EMRR which gets me in the ballpark.

    If you have one ( destroyed , built, open, new ) drop me a PM. I'm particularly interested in verifying the tubefin measurements and/or comparing your instruction sheet with the two I have.

    Cheers,
    -dh.
     
    Last edited: Feb 11, 2017
  2. Feb 8, 2017 #2

    dhbarr

    dhbarr

    dhbarr

    Amateur Professional

    Joined:
    Jan 30, 2016
    Messages:
    5,302
    Likes Received:
    439
    Quarterly Poke.
     
  3. Feb 8, 2017 #3

    Steve Piette

    Steve Piette

    Steve Piette

    Well-Known Member

    Joined:
    Feb 8, 2009
    Messages:
    46
    Likes Received:
    0
    I think your looking for one of these. I'll have to look for the instructions, it's been a decade or so since I last saw them.

    IMG_20170208_084425416.jpg
     
  4. Feb 8, 2017 #4

    dhbarr

    dhbarr

    dhbarr

    Amateur Professional

    Joined:
    Jan 30, 2016
    Messages:
    5,302
    Likes Received:
    439
    Yup, that's the one! The particular details I'm most interested in are ID, OD, tube root, tube tip; and NC length.

    Exciting stuff, thanks! Planning a BMS 52H downclone if I can get the details sorted.
     
  5. Feb 8, 2017 #5

    patelldp

    patelldp

    patelldp

    Well-Known Member

    Joined:
    Jan 23, 2009
    Messages:
    5,428
    Likes Received:
    29
    Someone a while back posted an STL for the cone and the tubing is XX Garolite 1.125" x 1.00" sourced from McMaster. LOC or BMS BT-50H slides inside.
     
  6. Feb 9, 2017 #6

    patelldp

    patelldp

    patelldp

    Well-Known Member

    Joined:
    Jan 23, 2009
    Messages:
    5,428
    Likes Received:
    29
  7. Feb 9, 2017 #7

    Steve Piette

    Steve Piette

    Steve Piette

    Well-Known Member

    Joined:
    Feb 8, 2009
    Messages:
    46
    Likes Received:
    0
    ID = 1.0"
    OD = 1.125"
    L = 10.0"

    NC = 4.25"

    Root = 2.0"
    Tip = 1.25"
     
  8. Feb 9, 2017 #8

    patelldp

    patelldp

    patelldp

    Well-Known Member

    Joined:
    Jan 23, 2009
    Messages:
    5,428
    Likes Received:
    29
    I didn't take the time to clean up the tube or cone too much, but here it is.

    ImageUploadedByRocketry Forum1486644667.955924.jpg

    ImageUploadedByRocketry Forum1486644685.342606.jpg
     
  9. Feb 9, 2017 #9

    Steve Piette

    Steve Piette

    Steve Piette

    Well-Known Member

    Joined:
    Feb 8, 2009
    Messages:
    46
    Likes Received:
    0
    Looks good Dan! I'm going to print a spare.
     
  10. Feb 9, 2017 #10

    patelldp

    patelldp

    patelldp

    Well-Known Member

    Joined:
    Jan 23, 2009
    Messages:
    5,428
    Likes Received:
    29
    Thanks, and smart idea! The shoulder lip requires some support, but you probably knew that. Otherwise, the shell should print fine.
     
  11. Feb 11, 2017 #11

    dhbarr

    dhbarr

    dhbarr

    Amateur Professional

    Joined:
    Jan 30, 2016
    Messages:
    5,302
    Likes Received:
    439
    So basically I should cut up my Go Devil 29 kit and do a build thread. Very well then! :cheers:
     

Share This Page