Tim51's Recent Activity

Help Support The Rocketry Forum by donating:

  1. Tim51 replied to the thread LOC oldies coming back?.

    Thanks!

    Jan 15, 2020 at 9:32 PM
  2. Tim51 liked g.pitts's post in the thread LOC oldies coming back?.

    I just happened to run across this link. Is this the one you are looking for? https://locprecision.com/product/wolverine/

    Jan 15, 2020 at 9:32 PM
  3. Tim51 liked g.pitts's post in the thread Loc Precision BIG NUKE 3E Kit.

    Personally, I wouldn’t do that. The downside is (as you’ve stated) getting them lined up such that you don’t cause a binding effect with...

    Jan 15, 2020 at 7:56 PM
  4. Tim51 replied to the thread LOC oldies coming back?.

    Is it listed under 5.5" kits on your website? I don't see it...

    Jan 15, 2020 at 7:56 PM
  5. Tim51 liked mike2wander's post in the thread MAC Performance 4" Bolt Two Stage Build.

    Our pleasure. The question comes up a lot and when I say 30% I get a lot of doubt sometimes. The scale speak no evil ;^)

    Jan 15, 2020 at 7:13 AM
  6. Tim51 replied to the thread MAC Performance 4" Bolt Two Stage Build.

    Thanks for taking the time to demonstrate the difference, Mike.

    Jan 14, 2020 at 10:49 PM
  7. Tim51 liked mike2wander's post in the thread MAC Performance 4" Bolt Two Stage Build.

    Both plates are .095" and measure 3.5" x 5.750" [ATTACH] [ATTACH]

    canvas weight.jpg fiberglass weight.jpg Jan 14, 2020 at 10:47 PM
  8. Tim51 liked ECayemberg's post in the thread LOC oldies coming back?.

    The original Wolverines were 37" of airframe and the short (13") cone, so 50". The *coming soon* Wolverines have 34" of airframe and...

    Jan 14, 2020 at 7:57 PM
  9. Tim51 replied to the thread LOC oldies coming back?.

    Assuming the original LaserLocs pre-dated common laser cutting of ply fins, were they named thus because they flew fast and straight,...

    Jan 14, 2020 at 7:57 PM
  10. Tim51 liked ECayemberg's post in the thread LOC oldies coming back?.

    Dear Jason.... [IMG] I need to update the LaserLoc thread...

    Jan 14, 2020 at 7:52 PM
  11. Tim51 liked Wallace's post in the thread MAC Performance 4" Bolt Two Stage Build.

    I know the tubes are quite a bit lighter, but if I remember correctly the fin stock is close as far as weight is concerned.

    Jan 14, 2020 at 6:34 AM
  12. Tim51 liked spigalau's post in the thread MAC Performance 4" Bolt Two Stage Build.

    The phenolic canvas is about 30% lighter than equivalent fiberglass products.

    Jan 13, 2020 at 8:23 PM
  13. Tim51 replied to the thread MAC Performance 4" Bolt Two Stage Build.

    Thanks!

    Jan 13, 2020 at 8:23 PM
  14. Tim51 liked TimothyAReed's post in the thread LOC Precision AMRAAM AIM 120C Build Thread.

    Build Log #10, Jan 13, 2020 I was able to meet the schedule and Complete the test flight on Jan 12, which was a success. I will...

    Jan 13, 2020 at 7:04 PM
  15. Tim51 replied to the thread MAC Performance 4" Bolt Two Stage Build.

    Very interesting build, thanks for the thread. Are the phenolic canvas fins alot lighter than they would be if they were G10 or G12?...

    Jan 13, 2020 at 5:08 PM