David Schwantz's Recent Activity

Help Support The Rocketry Forum by donating:

  1. David Schwantz replied to the thread Clear coat over wraps.

    hi Cowboy, I clear over all decals, do not want the edges to peel. After they do, you will never get them stuck back down. I use Mark at...

    Feb 23, 2020 at 3:45 PM
  2. David Schwantz replied to the thread I'm starting my L1 cert. research.

    But not as preeeeeety!

    Feb 22, 2020 at 8:58 PM
  3. David Schwantz replied to the thread South Dakota High Power is BACK! SDRJ has a field and waiver!.

    Hi HHaase, I belong to the MN Tripoli, both south and North, Glad th hear you have found a field. Our office is in Gary, SD, for work. I...

    Feb 22, 2020 at 2:19 AM
  4. David Schwantz replied to the thread Charge well size question.

    I have a 3" black hole and use1.4 grams of BP. If the well you are lookkking at will hold that amount, then I would think it should be fine.

    Feb 22, 2020 at 2:01 AM
  5. David Schwantz replied to the thread Charge well size question.

    If you have done ground tests, then you should know the amount of BP it will need to deploy. just buy the size that will fit that amount...

    Feb 22, 2020 at 12:47 AM
  6. David Schwantz replied to the thread Two Stage Conduit.

    I did not use conduit. I made a tunnel on the mmt. So if that counts, not past the mmt at all.

    Feb 22, 2020 at 12:45 AM
  7. David Schwantz replied to the thread Bad chutes for Jolly Logic Chute Release?.

    My lines are NEVER wrapped around the chute, they are folded neatly up one gore and then down a different one, then folded and JLCR...

    Feb 18, 2020 at 3:15 PM
  8. David Schwantz replied to the thread For Sale Aerotech Motors and Reloads.

    Hey Bob, I believe all but the H motor you can ship non hazmat, if that helps with sales.

    Feb 18, 2020 at 1:08 AM
  9. David Schwantz replied to the thread I'm starting my L1 cert. research.

    Thanks Nyt, I was looking for that and could not find it.

    Feb 17, 2020 at 11:42 PM
  10. David Schwantz replied to the thread 3D Printing What do you all think of this printer??.

    Hi Wallace, I would have to say "no". There is a double wall with a webbing in between. I assume vase mode would be a solid wall.

    Feb 17, 2020 at 11:41 PM
  11. David Schwantz replied to the thread I'm starting my L1 cert. research.

    There is no "stupid" question. You will get a lot of very good help from the guys on here. I did, and still do.

    Feb 17, 2020 at 10:29 PM
  12. David Schwantz replied to the thread I'm starting my L1 cert. research.

    If you go to that Apogee link I listed, in the middle of the chart it will give what those letters stand for. ie W = White Lightning...

    Feb 17, 2020 at 10:27 PM
  13. David Schwantz replied to the thread Using Kevlar as recovery harness attachment on 38mm min diam project.

    I also like to use large loops. Makes getting them through eye bolts that are already installed simple. Also more room to thread chutes...

    Feb 17, 2020 at 9:16 PM
  14. David Schwantz replied to the thread I'm starting my L1 cert. research.

    Most single use motors are composite, nothing to be afraid of. If you go to Apogee's web site, motor selection, choose dia that you are...

    Feb 17, 2020 at 9:12 PM
  15. David Schwantz replied to the thread Krylon Spray Paint Problem.

    You guys think that stuff stinks, try spraying Imron :)

    Feb 17, 2020 at 6:57 PM
Group Builder