BaddAzz Rocketry "Defender MkII"

The Rocketry Forum

Help Support The Rocketry Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
What are alt
Projection per given motor for this kit and do you think there is room for a tracker?

Yes, you can fit a rockethunter/consumer specialties in any rocket tube down to 29mm if you take it out of the case. I do this all the time for Blackhawk 29 flights. Walston, big red bee, and falcon types all fit 24mm.

Nice job there Eric!

Now get that website up so folks can buy 'em.
 
Yes, you can fit a rockethunter/consumer specialties in any rocket tube down to 29mm if you take it out of the case. I do this all the time for Blackhawk 29 flights. Walston, big red bee, and falcon types all fit 24mm.

Nice job there Eric!

Now get that website up so folks can buy 'em.

Thanks CJ!!

Working late Hours on that!
Now I'm old and Tired:)
 
Guys and Gals this has been fun!
I'm Honored by all the attention and interest in my rocket kits.

I will build the Myzztic next. I've put up some pic's and a video link on it.
Very special Rocket! Night launch ready, And of course it's

BADDAZZ​

Night launch was gonna be an option but I've decided to not do that.
I will not let you hose yourself out of the feature, It's just so SICK!!!
You deserve better than to lowball yourselves, there has been enough of that done to you already.
Price Less than Fifty
I'm working hard to hammer this down and I'm spending a chunk of coin to make it happen for you!

Okay I'll shut up!
Let's finish our DEFENDER MKII!!!

All we have to do is the chute, I'm sure most of you have your own way of doing this. I posting this for the guy that's never done it.

First get a paper clip and use needle nose to bend it as shown, this makes threading the shroud lines a breeze.

039.jpg

040.jpg
 
Last edited:
Now get your Chute Together Young Man!


Lay her flat, Place weight in middle (tail cone) tape down so it don't shift.
Lift lines up with build stick until they centered. Pinch these or tape together.

034.jpg

035.jpg

036.jpg

037.jpg
 
Last edited:
Push paper clip threader through hole on swivel,
hook lines onto threader, pull loop through swivel
remove threader and pass shroud loop over swivel and cinch it down.

041.jpg
 
Last edited:
Pass other end of swivel onto shock cord.

Tie a "Bowland on a bight knot" for this.
Make a big enough loop on elastic shock cord to pass over Nose cone.

042.jpg

043.jpg

044.jpg

045.jpg

046.jpg
 
Last edited:
Last Step! You are almost ready to Fly or Paint and Fly:wink:

Flake the gores on your Beautiful

Clemson Orange

"Top Flight Recovery" Parachute

AKA. Atmospheric Deaccelaration Device!!!
Don't forget your ADD or Your BaddAzz rocket will be BrokeAzz!!!


Fold as shown,
Add paint if you wish
Re-install Tailcone
Add Dogbarf/Wadding
Chute
Nosecone
Stuff a F24-7 and Fly the Heck out of Your DEFENDER MKII!!:headbang::wave::wave::headbang:

049.jpg

050.jpg

051.jpg

052.jpg

053.jpg
 
Last edited:
Do you have any idea when it will be ready to send out? I can't wait to build!
 
I realized as I went to bed I didn't load the launch lug build.

Check camera for pics...NADA :eek:

Rat Fartzz!:bang:

I'll shoot and post monday.
 
Last edited:
Hi Guys,

Sorry I didn't post this yesterday.
Worked all day in the MaddAzzLabb making BaddAzz rockets, Then I came home at 6:30ish and tilled up the front and side of the house. Came in grabbed a Much needed shower and supper about 9:00ish. My Old Butt Was Beat! So I'm posting this morning.

Let's wrap up The Defender MkII
Things you need:

Here are the lugs straight from machine, My hand got heavy on the deburr job.:bang:
Notice they are contoured to match air frame!!

PVC cleaner and cement
Ruler
Bamboo skewer or 3/16 rod 10" long
Masking tape
Sharpie
Sandpaper

Optional: Smokes and Coffee
CD player cranking out RUSH! Tom Sawyer if you please!!!:headbang:
Best Three Man Group in the known Universe!!!!

100_1701.JPG
 
Last edited:
First measure from aft end of PCV 1" forward and and another at 8".
Mark these locations with a sharpie.

Next, lightly sand over these spots with sandpaper.

100_1704.JPG

100_1705.JPG

100_1707.JPG
 
Right!

Place skewer and Lug on Frame and secure midway
with a wrap of masking tape.

Position Lugs in place conformal side down.

I had to say it
(Sure as crap someone out there would cement these upside down).:lol:

100_1712.JPG
 
Last step!

Glue'm On!!

Take a drop of PVC cement on a mix stick.

Gently lift Lug and apply cement to air frame.

Ok, Do the other one.

100_1713.JPG
 
PAYPAL IS UP!

The DefenderMkII ready for shipment, Also the Drop Dead Gourgeous MZZTIC!!!

Adding the ZZTARFIRE and DassBlitzkrieg Later this Morning!!

Still working on the details of MiZZ Rhonda!
 
Mine arrived! Build thread when I get the proper adhesives! I also want to add that the aluminum parts and nosecone feel no heavier than equivalent wood pieces. The body tube is also fairly light, probably no heavier than fiberglass. I was impressed by the fins, as they are EXACTLY the same. It all feels high quality. Eric: How is painting the PVC?
 
Last edited:
Mine arrived! Build thread when I get the proper adhesives! I also want to add that the aluminum parts and nosecone feel no heavier than equivalent wood pieces. The body tube is also fairly light, probably no heavier than fiberglass. I was impressed by the fins, as they are EXACTLY the same. It all feels high quality. Eric: How is painting the PVC?

Very light sanding #500, Light coat of Primer, wet sand #1000 shoot, cure, Clear. It's not hard to paint. If I did it, anyone can do it.:handshake:

Eric Foster
 
I'm excited to see where you guys take the make up.

Post Your BaddAzz Rocket Finished Your Way!!


Thanks

Eric Foster
 
Back
Top