Results 1 to 10 of 10
  1. #1
    Join Date
    3rd February 2012
    Location
    So Cal (ROC, TRASD, SCRA)
    Posts
    2,177

    ME-163 R/C From HK, with 18mm Motor

    Here's something interesting from HK, a ME-163 R/C plane with an 18mm motor mount. They're suggesting a C6-0, I suppose the idea is to use an extra channel to airstart it at some point in flight... don't know if that's NAR kosher.

    https://hobbyking.com/en_us/catalog/...-950mm-pnf-red


  2. #2
    Join Date
    27th January 2009
    Location
    Oregon
    Posts
    1,826
    Airstarting is ok, if you stick to the nar requirements if at an nar launch for min altitude before air start

    Instruction manual says:
    To prevent damage to the model, use only ‘capped’ type ‘single stage’ rocket engines. , hobbyking was suggesting plugging the motor to "cap it", ie not just a -0 as is to avoid ejecting the motor after burnout, and that is a motor modification according to NAR. In my opinion, the C-6 in a model of this weight is just a neat effect and isn't really doing anything for speed or altitude...ie a gimmick.

    You could use an 18mm RC motor, like the D-2.3 which has an 8 second burn and would look nice as an effect. or a single use 18mm composite with ejection charge removed which is not a modification.

    Air-starts. During stable, gliding flight of the R/C RBG, an attached motor may be air-started to increase the model’s altitude or airspeed without diving. This is permitted if:
    The onboard R/C ignition system is designed to not to be triggered accidentally, possesses an arm/disarm system, and is not armed until the model is on the pad with the radio system turned on and verified.
    The proposed airstart was reviewed and approved by the Range Safety Officer (if present) prior to launch.
    The model heading is not toward spectators.
    The model is at least 100 feet above the launch site.
    The pilot gives a loud countdown for the air-start.
    If the model descends below the minimum altitude for air-starts or the air-start fails, the model will be landed in a safe area, clear of people, and only the pilot or pilot’s appointed helper will be allowed to approach the model until the ignition system has been disarmed.

    Last edited by burkefj; 15th March 2017 at 05:08 PM.
    Manufacturer of 24mm RC Rocket Glider Kits: dynasoarrocketry.com

    Franks Rocketry and R/C Airplane Blog

  3. #3
    Join Date
    16th August 2016
    Location
    Paragould, Arkansas USA
    Posts
    233
    Absolutely cool. Even comes in an unpainted version! For those of us who want to get our JG 300 markings "just right".

    I have seen a 1/5th scale (big) Komet that had a D rocket motor with onboard ignition. But this was not meant for flight; it had an glow/gas engine up front, and the rocket motor was for smoke & effect on take-off.

    My impression is that this is the case as well (i.e., the rocket motor is for looks on take-off).
    "Lock S-foils in attack position....."

  4. #4
    Join Date
    27th January 2009
    Location
    Oregon
    Posts
    1,826
    I posted on the rcgroups thread, I'd like to see someone try 18mm composite D motors, sirrius has a plugged D-10 which would be more interesting, but they'd have to switch to a 12v e-switch setup to ignite it. Right now everyone over there is digging their ejection charges out and capping with epoxy, which people over here would freak out about as a motor modification. The 18mm composites don't need a modification, just remove paper cap and pour out bp.

    Frank
    Manufacturer of 24mm RC Rocket Glider Kits: dynasoarrocketry.com

    Franks Rocketry and R/C Airplane Blog

  5. #5
    Join Date
    27th January 2009
    Location
    Oregon
    Posts
    1,826
    It's interesting, the aerotech retail price on D-10P motors is $5.30 which isn't bad. I think this would be a great motor for some actual boost, or use the D-2.3 for an extended smoke trail and 8 second burn.

    I've also asked the AMA for clarification on their rules when flying at an AMA site, which say

    Rocket motors (using solid propellant) up to a G-series size may be used provided they remain attached to the model during flight. Model rockets may
    be flown in accordance with the National Model Rocketry Safety Code but may not be launched from model aircraft.

    This is sort of like the second amendment, it does not say that an RC plane with rocket assist is a model rocket and must follow NAR safety code. They are two distinct sentances.

    Which means, can you modify a motor by removing the ejection charge and still be ok under AMA but not NAR rules? One district rep said no, the other said they were not sure.

    If you do have to follow NAR safety rules for rocket powered rc planes when flying at an AMA field, then horizontal ground starts are NOT ok, you can only do air starts above 100' and you have to launch within 45 degrees of vertical for pure rocket takeoff. I specifically mentioned this model because a lot of people are plugging motors and flying them at ama sites.

    I know many people have their interpretations and beliefs, but I wanted AMA to give a direct clarification.

    Of course if you are flying at your own site you aren't bound by this.
    Manufacturer of 24mm RC Rocket Glider Kits: dynasoarrocketry.com

    Franks Rocketry and R/C Airplane Blog

  6. #6
    Join Date
    16th August 2016
    Location
    Paragould, Arkansas USA
    Posts
    233
    Just looking at the Durafly Me-163, I am wondering if the initial thought for the motor was to use the ejection charge to "pop out" the rocket motor.

    There does not appear to be an engine hook.
    "Lock S-foils in attack position....."

  7. #7
    Join Date
    27th January 2009
    Location
    Oregon
    Posts
    1,826
    No, it's just a foam pocket, instructions say to use a plugged motor and the videos talk about epoxy plugging a c6.
    Manufacturer of 24mm RC Rocket Glider Kits: dynasoarrocketry.com

    Franks Rocketry and R/C Airplane Blog

  8. #8
    Join Date
    18th January 2009
    Location
    Homewood, AL
    Posts
    3,242
    At an AMA field, AMA rules apply. NAR rules do not apply because it's not an NAR activity. It's a model plane, with a rocket motor, not a model rocket with wings.

    The problem would be with an NAR launch, wanting to do a horizontal takeoff. But I COULD see that happening, if the landowner allowed R/C planes to fly and it was flown as a Model Plane with a rocket motor. RSO could say no, not on "MY" range, but then if the landowner was OK with it, then it could take off somewhere other than the official rocket range (RSO does not "own" the land!), like any other R/C plane the landowner allowed to fly. Have to admit the chances are small that such an occasion would come up, but theoretically it's there.

    An R/C Modeler article in the early 1990's showed an ME-163 that was powered by an HPR motor. Perhaps J power.

    It took off horizontally, from grass. Very notable to me, because it used a balloon with water in the nose, to give it noseweight to counteract the tailweight of the propellant. When it started rolling, the end of a tube attached ot the ballon was unplugged, allowing water ot be squeezed out. And I used that idea for my X-1 and Orbital SkyDart booster to keep the CG from changing drastically, though I made mine gravity-fed with hollow tanks rather than a balloon.

    Also many years before that, articles.photos of R/C planes using "Rato", a rocket motor to assist take-off. One was simply like a 40" high-wing Cessna, with the engine under the fuselage and a bit behind the CG, at abut a 30 degree down angle so the thrust would not affect the pitch moment too badly and a vector of upwards thrust (it was often fired during the middle of takeoff run and was something like a C6 or D12).

    What the AMA code specifically bans rocketwise is firing "Missiles". And some jack.....persons have done that thru the years, 13mm missiles launched horizontally from R/C planes, to hit the ground. More importantly I think that is FAA illegal.

    Back to the Durafly model, they came out with this two years ago, in greenish camouflage. So it seems the new red one is a different color and some improvement to the wheeled drop-off dolly system. Here's a video:



    As for modifying motors to get rid of ejection charge...... none to remove in C6-0's. But there is a little bit of a forward fireball/pressurization even from a booster motor, which could cause it to pop out. I'm not sure that small vents would be a good idea on this.

    I have heard of some people who fly R/C RG's who are very sloppy with their mixing of 5-minute epoxy at times. Epoxy accidentally dripping into the forward end of booster motors..... which has the effect of plugging them, useless for staging. What to do with such booster motors when such epoxy mixing accidents occur?
    Last edited by georgegassaway; 20th March 2017 at 06:16 AM.

    Contest flying, Sport flying, it's all good.....
    2016 Bike Mileage total: 1843 miles. 5 Miles a day for the year!

  9. #9
    Join Date
    16th August 2016
    Location
    Paragould, Arkansas USA
    Posts
    233
    Quote Originally Posted by burkefj View Post
    No, it's just a foam pocket, instructions say to use a plugged motor and the videos talk about epoxy plugging a c6.
    Yeah, "ejection charge" and "foam" are not words that go together very well.....
    "Lock S-foils in attack position....."

  10. #10
    Join Date
    30th July 2014
    Location
    Fort Worth, TX
    Posts
    1,465
    I converted the original HK Me-163 to 18mm rocket assist, before they ever offered the second version with the rocket motor mount.

    A C6 actually gave a nice added boost after a flyby at half throttle, a pull up to about 45 degrees and an air ignition. More than an effect, less than a typical R/C rocket glider.

    I bought some D10s to try at some point.

    Tom Blakeney
    NAR 52002 L1, AMA 28682
    2016 launches so far: 36: 2 HP, 7 MP, 6 LP, 21 R/C RG. R/C Chute Sled: 8 for 8!

Similar Threads

  1. 18mm motor adapter
    By Screaminhelo in forum Propulsion
    Replies: 11
    Last Post: 20th August 2014, 03:04 PM
  2. [SOLD!] GMA 13mm & 18mm 3 Motor Set
    By Artsey in forum Yard Sale / Wanted
    Replies: 7
    Last Post: 18th February 2012, 03:50 AM
  3. 18mm F Motor
    By ScrapDaddy in forum The Watering Hole
    Replies: 5
    Last Post: 11th September 2010, 07:59 AM
  4. 18mm motor poll
    By caheaton in forum Low Power Rocketry (LPR)
    Replies: 24
    Last Post: 30th October 2008, 08:19 PM
  5. Quiest 18mm D motor Question
    By superdave in forum Low Power Rocketry (LPR)
    Replies: 2
    Last Post: 26th July 2005, 03:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •