-
Older Activity
-
19th October 2017, 03:20 PM
Keep in mind, you do build a DMS. It's much the same as a RMS, just with a single use case. Bah... I thought so, but maybe it's only the larger...
8 replies | 408 view(s)
-
19th October 2017, 03:13 PM
Eggtimer stuff should work with some frequency reuse. It has an ID that the receiver looks for and ignores other transmitters on the same frequency....
29 replies | 875 view(s)
-
19th October 2017, 01:06 AM
You should send me one to test and review.... :)
Always great stuff to work with.
29 replies | 875 view(s)
-
18th October 2017, 08:10 PM
I've flown 1 Loki load. M900 for my L3 cert. Great motor for the 76/6000 case. :)
I plan to get more, but fell down the EX rabbit hole and need...
27 replies | 608 view(s)
-
17th October 2017, 04:46 PM
I've only built one Loki M, but I was also worried about getting the remains of the smoke grain out after the flight. It ended up not being a...
14 replies | 410 view(s)
-
17th October 2017, 04:40 PM
Antennas will vary in performance for everyone. A good place to start is something like this..
https://www.antennaweb.org/
It gives you a good...
19 replies | 427 view(s)
-
16th October 2017, 03:30 PM
The first thing to decide is if you want to go down the home server rabbit hole. It can get... Interesting... Fast. :) Emby, Plex, Kodi are the big...
19 replies | 427 view(s)
-
16th October 2017, 12:21 AM
Cool. I'll be ordering one. :)
And probably some other stuff. Eggtimer is both good and bad for my wallet...
29 replies | 875 view(s)
-
5th October 2017, 02:43 AM
I might be interested, depending on pricing etc.. Any idea what weight looks like?
12 replies | 527 view(s)
-
2nd October 2017, 06:47 PM
I would posit that "Doing Something" without any idea of what it is or how it affects things is worse than doing what appears to be nothing while...
61 replies | 1630 view(s)
-
2nd October 2017, 06:10 PM
Programmers tend to look down on things like this, but as a tool to learn and/or create simple interfaces I think it makes a lot of sense. The code...
15 replies | 505 view(s)
-
2nd October 2017, 05:25 PM
Here's the thing though... I doubt there is a single root cause, or even just a few. By all means, do the research! But these sorts of issues are...
61 replies | 1630 view(s)
-
29th September 2017, 06:32 PM
One thought I wanted to toss out there, I have no idea how well this would work or if there would be too many possible issues with it...
GSE and...
156 replies | 11890 view(s)
-
29th September 2017, 06:10 PM
It would definitely fill a gap. I don't own any 29mm hybrids. I think SRS was the only ones that made one, and at the time electronics were larger...
156 replies | 11890 view(s)
-
29th September 2017, 04:57 PM
I would avoid the I55 as well, unless you can launch in near windless conditions. Of course, I'm one to talk, my L3 simmed to 42fps off the rail. I...
92 replies | 1962 view(s)
-
28th September 2017, 04:26 PM
Quick thought for testing. If you can, use electronic deployment and a threaded forward closure. Then put an eyebolt in the FC and tether it to the...
30 replies | 762 view(s)
-
28th September 2017, 05:20 AM
Here's the SCAD and 38mm STLs for a simple threaded retainer. You might need to adjust the ID to match whatever MMT you use.
Note that it has not...
30 replies | 762 view(s)
-
27th September 2017, 08:20 PM
- Check AGAIN that you REALLY turned on the electronics...
Not that I've ever done that.... maybe..... so far as you know.... :)
92 replies | 1962 view(s)
-
27th September 2017, 08:18 PM
Sounds good. I'm planning to be there, so feel free to come by and ask questions etc.. I can bring my L3 av-bay if you want to see one guy's way of...
13 replies | 526 view(s)
-
27th September 2017, 04:45 PM
While I wouldn't mind having it as a backup deployment, I see why manufacturers might not want to pay to certify them that way. And I have read a...
13 replies | 526 view(s)
-
27th September 2017, 07:55 AM
Since you are in UT, try to come out to a UROC launch. There are a number of us that can get you up to speed on deployment electronics. You can even...
13 replies | 526 view(s)
-
26th September 2017, 08:55 PM
I'll dig around, I started modifying an OpenSCAD script to build a motor retainer. I had to tinker with clearances and such, but I think I have a...
30 replies | 762 view(s)
-
26th September 2017, 08:49 PM
Good to hear at least one manufacturer is still around.
I got distracted from Hybrids on my L3 project and flight. That has been successfully...
156 replies | 11890 view(s)
Total Posts
- Total Posts
- 915
- Posts Per Day
- 0.29
General Information
- Last Activity
- Today 04:12 AM
- Join Date
- 19th January 2009
- Referrals
- 0
| |
|
Find latest posts
