Help Support RocketryForum by donating using the link above or becoming a Supporting Member.


  1. 13th September 2017
    Views:
    973
  2. 8th April 2014
    Views:
    13,955
Page 3 of 273 FirstFirst 1 2 3 4 5 6 7 13 53 103 ... LastLast
Threads 41 to 60 of 5447

Forum: Techniques

Share your modeling techniques with other builders.

  1. Where to find card stock like Estes uses.

    Started by DeepOvertone, 24th January 2018 07:08 PM
    • Replies: 18
    • Views: 782
    29th January 2018, 09:52 AM Go to last post
  2. Compressor best practises and HVLP setup

    Started by mpitfield, 19th April 2016 01:57 AM
    2 Pages
    1 2
    • Replies: 49
    • Views: 6,115
    25th January 2018, 08:04 PM Go to last post
    • Replies: 4
    • Views: 300
    25th January 2018, 02:00 PM Go to last post
  3. TCP Global HVLP Set: Is it worth it?

    Started by Tobor, 4th January 2018 01:27 AM
    • Replies: 10
    • Views: 446
    24th January 2018, 05:48 PM Go to last post
  4. Effect of Sharpie on glue joints

    Started by neil_w, 9th January 2018 10:48 PM
    • Replies: 9
    • Views: 716
    19th January 2018, 04:31 AM Go to last post
  5. Spray paint Nozzle

    Started by mjennings, 17th January 2018 03:23 AM
    • Replies: 1
    • Views: 149
    17th January 2018, 03:43 AM Go to last post
  6. Extruded Polystyrene Blocks

    Started by Gary Byrum, 18th December 2017 05:11 PM
    2 Pages
    1 2
    • Replies: 49
    • Views: 1,420
    17th January 2018, 12:15 AM Go to last post
  7. Lego guillotine fin alignment

    Started by barn, 26th October 2017 03:55 PM
    • Replies: 26
    • Views: 1,619
    7th January 2018, 05:28 AM Go to last post
  8. EggFinder TX, RX, and EggTimer Quark assembly

    Started by DanielLW, 1st January 2018 02:56 PM
    • Replies: 28
    • Views: 1,194
    6th January 2018, 09:06 PM Go to last post
  9. Working with Carbon Fiber and Aluminum

    Started by Swissyhawk, 28th December 2017 07:57 PM
    • Replies: 6
    • Views: 400
    1st January 2018, 12:05 AM Go to last post
  10. Sanding G12 fiberglass to fit coupler to airframes

    Started by billdz, 27th December 2017 06:10 PM
    • Replies: 15
    • Views: 634
    29th December 2017, 08:31 PM Go to last post
  11. Anybody use "Fin Pockets"

    Started by rharshberger, 12th December 2015 08:58 PM
    2 Pages
    1 2
    • Replies: 45
    • Views: 6,274
    28th December 2017, 08:18 PM Go to last post
  12. What's the problem with JB KwikWeld?

    Started by billdz, 24th December 2017 12:23 AM
    • Replies: 28
    • Views: 1,314
    28th December 2017, 01:51 AM Go to last post
  13. Retention After The Build

    Started by Normzilla, 23rd December 2017 04:07 AM
    • Replies: 8
    • Views: 422
    24th December 2017, 01:51 AM Go to last post
  14. Can Anyone Recommend a Router

    Started by DRAGON64, 22nd December 2017 12:50 PM
    • Replies: 3
    • Views: 332
    22nd December 2017, 06:05 PM Go to last post
    • Replies: 28
    • Views: 2,486
    21st December 2017, 10:33 PM Go to last post
  15. Aerogloss Sanding Sealer Over CA?

    Started by RocketFeller, 20th December 2017 04:37 PM
    • Replies: 3
    • Views: 200
    20th December 2017, 06:03 PM Go to last post
  16. Fin beveling service

    Started by Big_Red_Daddy, 19th December 2017 09:53 PM
    • Replies: 3
    • Views: 376
    20th December 2017, 12:57 AM Go to last post
  17. How to get balsa nose cones smooth

    Started by rockets, 18th December 2017 04:21 PM
    • Replies: 7
    • Views: 367
    18th December 2017, 11:17 PM Go to last post
    • Replies: 4
    • Views: 329
    15th December 2017, 06:23 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •