1. 8th April 2014
    Views:
    11,474
Page 1 of 264 1 2 3 4 5 11 51 101 ... LastLast
Threads 1 to 20 of 5269

Forum: Techniques

Share your modeling techniques with other builders.

  1. Primer and topcoat in the same session?

    Started by neil_w, 31st March 2017 04:28 PM
    • Replies: 20
    • Views: 768
    19th April 2017, 05:08 PM Go to last post
  2. 3D printer recommendations

    Started by Winston, 17th April 2017 07:29 PM
    • Replies: 3
    • Views: 226
    19th April 2017, 09:21 AM Go to last post
  3. Bondo or filler for spiral grooves

    Started by Kirk G, 9th May 2015 06:19 PM
    • Replies: 27
    • Views: 2,958
    19th April 2017, 04:54 AM Go to last post
  4. 2 Part expanding Foam question?

    Started by AfterBurners, 16th April 2017 04:53 AM
    • Replies: 8
    • Views: 338
    18th April 2017, 05:39 PM Go to last post
  5. Glassing a nose cone

    Started by ActingLikeAKid, 16th April 2017 04:56 AM
    • Replies: 8
    • Views: 282
    17th April 2017, 05:01 PM Go to last post
  6. Whats your technique for removing shear pins?

    Started by Locksmith, 15th April 2017 01:15 AM
    • Replies: 15
    • Views: 444
    17th April 2017, 03:06 PM Go to last post
  7. Is TiteBond Strong Enough?

    Started by Woody's Workshop, 17th April 2017 03:00 PM
    • Replies: 0
    • Views: 127
    17th April 2017, 03:00 PM Go to last post
  8. LOC King Viper III - practical, not perfect

    Started by dixontj93060, 2nd January 2017 05:04 PM
    2 Pages
    1 2
    • Replies: 47
    • Views: 3,288
    15th April 2017, 11:15 PM Go to last post
  9. 3D Printed Electronics Sled

    Started by ecarson, 12th April 2017 11:50 PM
    • Replies: 12
    • Views: 345
    15th April 2017, 05:51 AM Go to last post
  10. Scientists Shed New Light on Knots

    Started by lowga, 13th April 2017 10:07 AM
    • Replies: 2
    • Views: 264
    15th April 2017, 03:06 AM Go to last post
  11. Plastic Rivets, Cutting Kevlar, Airframe / Fin Repairs

    Started by gsanders, 10th April 2017 05:43 PM
    • Replies: 22
    • Views: 629
    12th April 2017, 04:43 PM Go to last post
  12. Launch a wing

    Started by AfterBurners, 10th April 2017 06:16 PM
    • Replies: 10
    • Views: 315
    11th April 2017, 06:05 PM Go to last post
  13. Post Your Jigs and Such

    Started by Dave A, 1st February 2016 03:13 PM
    3 Pages
    1 2 3
    • Replies: 88
    • Views: 9,829
    8th April 2017, 08:46 PM Go to last post
  14. Paint removal off of a plastic nose cone

    Started by redleder, 3rd April 2017 08:41 PM
    • Replies: 29
    • Views: 658
    8th April 2017, 05:50 PM Go to last post
  15. Polyspan and dope for covering tube spiral seam

    Started by Q-Aero, 6th April 2017 02:35 AM
    • Replies: 1
    • Views: 148
    6th April 2017, 05:44 AM Go to last post
  16. BSI 20 minute finishing epoxy

    Started by AfterBurners, 4th April 2017 03:17 AM
    • Replies: 4
    • Views: 230
    5th April 2017, 06:00 PM Go to last post
  17. Fin repair

    Started by billdz, 4th April 2017 09:34 PM
    • Replies: 7
    • Views: 233
    5th April 2017, 03:21 PM Go to last post
  18. Bad luck with metallic paints

    Started by BDB, 31st March 2017 04:47 AM
    • Replies: 28
    • Views: 738
    5th April 2017, 01:37 AM Go to last post
    • Replies: 4
    • Views: 263
    1st April 2017, 06:55 AM Go to last post
  19. Non-toxic paint

    Started by KL2IE, 26th March 2017 08:15 PM
    • Replies: 11
    • Views: 538
    28th March 2017, 03:29 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •