Help Support RocketryForum by donating using the link above or becoming a Supporting Member.


  1. 13th September 2017
    Views:
    785
  2. 8th April 2014
    Views:
    13,760
Page 1 of 271 1 2 3 4 5 11 51 101 ... LastLast
Threads 1 to 20 of 5411

Forum: Techniques

Share your modeling techniques with other builders.

  1. Those who use airbrush to paint what brand of paint do you use?

    Started by solid_fuel, 22nd December 2017 03:05 AM
    2 Pages
    1 2
    • Replies: 40
    • Views: 861
    Today, 07:12 PM Go to last post
  2. LOC King Viper III - practical, not perfect

    Started by dixontj93060, 2nd January 2017 05:04 PM
    3 Pages
    1 2 3
    • Replies: 64
    • Views: 4,900
    Yesterday, 07:34 PM Go to last post
  3. Effect of Sharpie on glue joints

    Started by neil_w, 9th January 2018 10:48 PM
    • Replies: 8
    • Views: 357
    Yesterday, 05:08 AM Go to last post
  4. Spray paint Nozzle

    Started by mjennings, Yesterday 03:23 AM
    • Replies: 1
    • Views: 77
    Yesterday, 03:43 AM Go to last post
  5. Extruded Polystyrene Blocks

    Started by Gary Byrum, 18th December 2017 05:11 PM
    2 Pages
    1 2
    • Replies: 49
    • Views: 933
    Yesterday, 12:15 AM Go to last post
  6. Best method to cut ply?

    Started by Rktman, 31st December 2017 09:13 PM
    2 Pages
    1 2
    • Replies: 44
    • Views: 1,087
    10th January 2018, 07:28 PM Go to last post
  7. Lego guillotine fin alignment

    Started by barn, 26th October 2017 03:55 PM
    • Replies: 26
    • Views: 1,362
    7th January 2018, 05:28 AM Go to last post
  8. EggFinder TX, RX, and EggTimer Quark assembly

    Started by DanielLW, 1st January 2018 02:56 PM
    • Replies: 28
    • Views: 753
    6th January 2018, 09:06 PM Go to last post
  9. TCP Global HVLP Set: Is it worth it?

    Started by Tobor, 4th January 2018 01:27 AM
    • Replies: 0
    • Views: 83
    4th January 2018, 01:27 AM Go to last post
  10. Compressor best practises and HVLP setup

    Started by mpitfield, 19th April 2016 01:57 AM
    2 Pages
    1 2
    • Replies: 47
    • Views: 5,411
    3rd January 2018, 02:43 AM Go to last post
  11. Working with Carbon Fiber and Aluminum

    Started by Swissyhawk, 28th December 2017 07:57 PM
    • Replies: 6
    • Views: 292
    1st January 2018, 12:05 AM Go to last post
  12. Sanding G12 fiberglass to fit coupler to airframes

    Started by billdz, 27th December 2017 06:10 PM
    • Replies: 15
    • Views: 463
    29th December 2017, 08:31 PM Go to last post
  13. Anybody use "Fin Pockets"

    Started by rharshberger, 12th December 2015 08:58 PM
    2 Pages
    1 2
    • Replies: 45
    • Views: 5,654
    28th December 2017, 08:18 PM Go to last post
  14. What's the problem with JB KwikWeld?

    Started by billdz, 24th December 2017 12:23 AM
    • Replies: 28
    • Views: 1,025
    28th December 2017, 01:51 AM Go to last post
  15. Retention After The Build

    Started by Normzilla, 23rd December 2017 04:07 AM
    • Replies: 8
    • Views: 307
    24th December 2017, 01:51 AM Go to last post
  16. Can Anyone Recommend a Router

    Started by DRAGON64, 22nd December 2017 12:50 PM
    • Replies: 3
    • Views: 248
    22nd December 2017, 06:05 PM Go to last post
    • Replies: 28
    • Views: 2,049
    21st December 2017, 10:33 PM Go to last post
  17. Aerogloss Sanding Sealer Over CA?

    Started by RocketFeller, 20th December 2017 04:37 PM
    • Replies: 3
    • Views: 137
    20th December 2017, 06:03 PM Go to last post
  18. Fin beveling service

    Started by Big_Red_Daddy, 19th December 2017 09:53 PM
    • Replies: 3
    • Views: 286
    20th December 2017, 12:57 AM Go to last post
  19. How to get balsa nose cones smooth

    Started by rockets, 18th December 2017 04:21 PM
    • Replies: 7
    • Views: 270
    18th December 2017, 11:17 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •